2.4 GHz 2-Line Cordless
Speakerphone
43-3701
Thank you for purchasing a RadioShack 2.4 GHz Cordless Telephone.
Your phone uses advanced technology to give you superior audio
quality and extended range. The
phone’s Caller ID unit records each
caller’s telephone number (and name, if
available in your area) and the date and
time of the call, as provided by your local
phone company to Caller ID service
subscribers. If you subscribe to Call
Waiting with Caller ID, the phone shows
you the incoming caller information,
even when you are already talking on
the phone.
40-Number Memory Dialing — lets you
store up to 40 numbers in memory for
easy dialing.
Ample Talk and Standby Time — the
supplied battery (when fully charged)
provides about 7 hours of talk time or 14
days of standby time.
Headset Jack — lets you connect an
optional headset for hands-free
convenience. (See “Using a Headset” on
page 37.)
Auto Talk— lets you set the phone to
answer a call by simply lifting the handset
from the base.
IMPORTANT
!
!
If an icon appears at the end of a paragraph, go to the box on that page with the
corresponding icon for pertinent information.
"
Ó — Hint
Ô — Note
— Warning
— Important
— Caution
!
o
OWNER’S MANUAL
Please read before using this equipment.
© 2003 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks
used by RadioShack Corporation.
ENERGYSTAR and the ENERGYSTAR certification mark
are registered US marks.
line has been disconnected at the
network interface.
CONTENTS
(continued)
Chain Dialing .................. 29
Editing a Stored Name
and/or Phone Number .... 30
Erasing a Stored Name
6. Use caution when installing or
modifying telephone lines.
and Phone Number ......... 31
Caller ID Features .............. 32
Caller ID .......................... 32
When the Telephone
Rings ............................... 33
Viewing the Caller ID
7. Do not fix the AC power supply cord to
building surfaces with metal fittings (if
the product has an AC power cord).
Message List ................... 33
Using the Caller ID List ... 34
Deleting Information from
8. Unplug this product from the wall outlet
before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
the Caller ID List ............. 36
Using CIDCW (Caller ID on
Call Waiting) .................... 37
Using a Headset ................. 37
Troubleshooting .................. 39
Care .................................... 40
Service and Repair ............. 40
FCC Statement ............... 40
Surge Proection .............. 41
9. Do not use this product near water, for
example, near a bathtub, wash bowl,
kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
10. Do not place this product on an
unstable cart, stand, or table. The
product may fall, causing serious
damage to the product.
11. Slots and openings in the cabinet and
the back or bottom are provided for
ventilation. To protect it from
overheating, these openings must not
be blocked or covered. The openings
should never be blocked by placing the
product on a bed, sofa, rug, or other
similar surface. This product should
never be placed near or over a radiator
or heat register.This product should not
be placed in a built-in installation
unless proper ventilation is provided.
12. This product should be operated only
from the type of power source indicated
on the marking label. If you are not sure
of the type of power supply to your
home, consult your local power
company.
3
13. Do not allow anything to rest on the power cord. Do not locate this
product where the cord will be stepped on.
14. Do not overload wall outlets and extension cords as this can result in
a risk of fire or electric shock.
15. Never push objects of any kind into this product through cabinet slots
as they may touch dangerous voltage points or short out parts that
could result in a risk of fire or electric shock. Never spill liquid of any
kind on the product.
16. To reduce the risk of electric shock, do not disassemble this product.
Take it to a qualified service technician when service or repair work
is required. Opening or removing covers may expose you to
dangerous voltage or other risks. Incorrect reassembly can cause
electric shock when the product is subsequently used.
17. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
• When the power cord plug is damaged or frayed.
• If liquid has been spilled, into the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally by following the
operating instructions. Adjust only those controls that are covered
by the operating instructions because improper adjustment of
other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to
normal operation.
• If the product has been dropped or the cabinet has been
damaged.
• If the product exhibits a distinct change in performance.
18. Avoid using a telephone during an electrical storm. There may be a
remote risk of electric shock from lightning.
19. Do not use the telephone to report a gas leak in the vicinity of the leak.
4
BATTERY SAFETY INSTRUCTIONS
To reduce the risk of fire or injury, read and follow these instructions
1. Use only the same type and size battery pack specified in the
instruction manual provided for this product.
2. Do not dispose of the battery pack in a fire. The cell may explode.
Check with local codes for possible special disposal instructions.
3. Do not open or mutilate the battery pack. Released electrolyte is
corrosive and may cause damage to the eyes or skin. It may be toxic
if swallowed.
4. Exercise care in handling the battery pack in order not to short it with
conducting materials such as rings, bracelets, and keys. The battery
or conductor may overheat and cause burns.
5. Charge the battery pack provided or identified for use with this
product only in accordance with the instructions and limitations
specified in the instruction manual provided for this product.
6. Observe proper polarity orientation between the battery pack and
battery charger.
SAVE THESE INSTRUCTIONS
5
INTRODUCTION
IMPORTANT
!
!
•
When AC power is lost, the
phone loses the security access-
protection code connection
between the base and the hand-
set. When power is restored, put
the handset on the base briefly
to restore this connection so you
can use the handset.
Your phone operates on
standard radio frequencies as
allocated by the FCC.
It is possible for other radio
units operating nearby on similar
frequencies to unintentionally
intercept your conversation or
cause interference. This possible
lack of privacy can occur with
any cordless phone.
Cordless phones require AC power to
operate. When the power is off, you cannot
make or receive calls using your phone.
You should also have a phone that does not
need AC power to operate (not a cordless
phone), so you can still make and receive
•
•
calls if there is an AC power failure.
!
INSTALLATION
Before using your phone, carefully peel the
protective film off the display. The film
protects the handset window during
shipment and is not necessary for use.
Ô NOTES Ô
•
Your telephone connects directly
to a modular telephone line jack.
If your telephone wiring does not
have a modular jack, you can
update the wiring yourself using
jacks and adapters (available at
your local RadioShack store), or
have the telephone company
update the wiring for you. You
must use compatible modular
jacks that are compliant with
Part 68 of FCC Rules.
MOUNTING THE PHONE
You can place the phone’s base on a desk
or table, or mount it on a standard wall plate
or directly on a wall. Choose a location that
is:
• near an AC outlet
•
•
•
The line that connects a two-line
phone jack to the phone
• near a modular telephone line jack
• out of the way of normal activities
company wiring must be
twisted-pair cable. Otherwise,
you might hear interference
(crosstalk) between the two
lines.
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
The line that connects a two-line
phone jack to the phone
company wiring must be
twisted-pair cable. Otherwise,
you might hear interference
(crosstalk) between the two
lines.
• away from other cordless phones
If your home has specially wired
alarm equipment connected to
the telephone line, be sure that
installing the system does not
disable your alarm equipment. If
you have questions about what
will disable alarm equipment,
contact your telephone company
or a qualified installer.
The base’s location affects the handset’s
range. If you have a choice of several
locations, try each to see which provides the
best performance. Ô
•
The USOC number of the two-
line jack to be installed is RJ14C
(RJ14W for a wall plate). The
USOC number of a single- line
jack is RJ11C.
6
Connecting to the Phone Lines
To take full advantage of the phone’s
capabilities, you must have two phone lines
with separate phone numbers. If you have
only one line, you can order a second from
your phone company. "
"
CAUTION
"
•You must use a
Class 2 power
source that
!
supplies 9V DC
and delivers at least 350 mA.
Its center tip must be set to
positive and its plug must fit
the phone's DC IN 9V jack.
The supplied adapter meets
these specifications. Using an
adapter that does not meet
these specifications could
damage the phone or the
adapter.
You can connect the phone to the lines in
one of three ways:
• connect two lines through a two-line
modular phone jack
• connect two lines through two one-line
modular phone jack
•
Always connect the AC
adapter to the phone before
you connect it to AC power.
When you finish, disconnect
the adapter from AC power
before you disconnect it from
the phone.
• connect one line through a one-line
modular phone jack.
• If you connect the phone to a two-line
phone jack with a two-line cord, do not
connect a third line to the TEL LINE 2
jack or the phone will not operate
properly. Instead, you can connect
another phone device, such as a fax
machine or modem.
• To connect the phone to two one-line
phone jacks, plug one end of the
supplied long two-line modular cord
into TEL LINE 1/2 and plug another cord
(not supplied) into the TEL LINE 2 jack.
Route both cords through the strain-
relief slot on the base.
On a Desk Top
1. To connect the
phone to a two-
line phone jack,
plug one end of
the supplied long
two-line modular
cord into the TEL
LINE 1/2 jack on
DC IN 9V TEL LINE
7
the back of the phone. Route the cord
through the strain-relief slot on the
base. Ô
Ô NOTE Ô
To connect the phone to a
single one-line phone jack,
plug one end of the
supplied long modular cord
into the TEL LINE 1/2 or
TEL LINE 2 jack. Route the
cord through the strain-
relief slot on the base.
2. Plug the supplied AC adapter’s barrel
plug into the DC IN 9V jack on the back
of the base and route the adapter’s
cord through the strain relief slot on the
bottom of the base.
3. Plug the adapter into a standard AC
outlet.
4. Connect the phone cord(s) to the
modular phone line jack(s).
5. Raise the base’s antenna to a vertical
position.
On a Wall Plate
1. Connect the phone line(s) as described
in “On a Desk Top”. Use the shorter
modular cord to mount the phone on
the wall plate.
2. Insert the supplied AC adapter’s barrel
plug into the DC IN 9V jack on the back
of the base.
3. Route the adapter’s cord through the
narrow groove on the base. If you are
using two phone cords, route the
second cord through one of the wide
grooves on the base.
4. Plug the other end of the short modular
cord into the wall plate jack, then align
the keyhole slots with the wall plate
studs and slide the base downward to
secure it. If you are using two phone
cords, plug the second cord into the
second phone jack.
8
5. Plug the adapter into a standard AC
outlet.
6. Press and lift out the handset holder,
flip it over, then snap it back into place.
7. Raise the base’s antenna to a vertical
position.
Ô NOTE Ô
On a Wall
To mount the phone directly
on a wall, you need two
15
1. Drill two holes 3 /16 inches (100 mm)
3
apart. Then thread a screw into each
hole, letting the heads extend about /8
inch (3 mm) from the wall. Ô
screws of at least 1 /8 inch
1
long (not supplied) with
heads that fit into the
keyhole slots on the bottom
of the base. Follow the
steps under “On a Wall ” on
Page 9, then apply these
additional instructions for
placement on a wall.
2. Plug one end of the supplied long
modular cord into the TEL LINE 1/2 jack
on the back of the base.
To connect the phone to two one-line
jack, plug another cord (not supplied)
into the TEL LINE 2 jack.
3. Route the adapter cable and modular
cord(s) through the grooves on the
base.
4. Align the base’s keyhole slots with the
mounting screws and slide the base
downward to secure it.
CONNECTING/CHARGING THE
BATTERY PACK
The phone comes with a rechargeable
nickel-cadmium battery pack in the handset,
but not connected. Before using your
phone, you must connect the battery pack,
then charge it for about 15–20 hours.
9
1. Press down and slide
off the battery
compartment cover.
2. Lift the battery pack
out of the
compartment.
3. Plug the battery pack’s connector into
the socket in the compartment (the
connector fits only one way), then place
the battery pack in the compartment.
4. Replace the cover.
!
IMPORTANT
!
!
Be sure the battery pack is
properly connected before you
try to charge it. The CHARGE/
IN USE LED lights when the
handset is on the base, even if
the battery pack is not
To charge the battery pack, place the
handset on the base. The CHARGE/IN USE
LED on the base lights.
Low
Recharge the battery pack when
connected.
Battery
flashes on the display.
If you have trouble replacing the battery
pack, take the phone to your local
RadioShack for assistance.
Recharging the Battery Pack
When you first use the phone after charging
or recharging the battery pack, the phone
might not work and you might hear an error
tone when you press Line 1 or Line2. While
holding INTERCOM on the base, return the
handset to the base for about 3 seconds to
change the security access-protection code.
If the base loses power for about an hour
while the handset is away from it, the
security access-protection code might be
lost. To change the code, while holding
INTERCOM on the base, return the handset
to the base for about 3 seconds.
10
If the battery pack becomes weak during a
call, the handset beeps every 3 seconds
WARNING
o
o
Dispose of the old battery
pack promptly and properly.
Do not burn or bury it. See
“Battery Safety Instructions”
on page 5 for additional
information on proper
Low Battery
and
flashes. When this
happens, you cannot make a call until you
recharge the battery pack.
If the display is blank and the phone does
not work, recharge the battery pack. (The
battery power might be too low to light the
display.)
battery handling.
About once a month, fully discharge the
battery by keeping the handset off the base
IMPORTANT
!
!
The EPA
Low Battery
until
flashes on the display.
certified RBRC®
Battery
Otherwise, the battery pack loses its ability
to fully recharge.
Recycling Seal
on the nickel-
cadmium (Ni-Cd) battery
indicates RadioShack is
The handset loses its security access-
protection code if the battery pack is
completely discharged. While holding
INTERCOM on the base, place the handset
on the base to recharge the battery pack
and change the code.
voluntarily participating in an
industry program to collect
and recycle these batteries at
the end of their useful life,
when taken out of service in
the United States or Canada.
The RBRC program provides a
convenient alternative to
placing used Ni-Cd batteries
into the trash or the municipal
waste stream, which may be
illegal in your area. Please call
1-800-THE-SHACK (1-800-
843-7422) for information on
Ni-Cd battery recycling and
disposal bans/restrictions in
your area. RadioShack’s
Using a pencil eraser, clean the charging
contacts on the handset and base about
once a month.
If you are not going to use your phone for an
extended period, disconnect the battery
pack. This increases the battery pack’s
usable life.
The supplied battery pack should last for
about a year. If the battery pack does not
hold a charge for more than 2 hours after an
overnight charge, replace it with a new 3.6-
volt, 600 mAh battery pack with a connector
that fits the socket in the battery
involvement in this program is
part of the company’s
commitment to preserving our
environment and conserving
our natural resources.
compartment. You can order a replacement
battery pack through RadioShack. Install
the new battery pack and charge it for about
15–20 hours. o !
11
BASICS
MAKING AND RECEIVING
CALLS
Basic 2-line operation Ô
Ô NOTES Ô
Handset On
Handset Off
Base
•
•
You must have a 2- line
subscription from your
phone company to use
the 2-line features.
Action
Base Only
Base Ô
Pick up the
handset (Auto line 2, any
Talk) or pick up number,
Press line 1or Press line 1
or line 2.
To
See “To Change Your
Auto Talk and CIDCW:”
on page 22.
answer the handset
a call and press
line 1
/tone/< or
#/> keys (Auto
Talk: On).
or line 2.
1)Pick up the
handset.
2)Press line 1 2)Listen for
or line 2.
3)Listen for the
dial tone.
4)Dial the
number.
1)Press line 1 1)Press
or line 2. line 1 or
line 2.
2)Listen for
the dial
the dial
tone.
3)Dial the
number.
OR
tone.
To
3)Dial the
number.
makea
call
OR
1)Pick up the
handset.
2)Dial the
number, then
press line 1
or line 2.
Dial the
number, then
press line 1 or
line 2.
12
Handset On
Base Ô
Handset Off
Base
Action
Base Only
To
hang
up
Press line 1 or line 2, or return Press line 1
the handset to the base (Auto
Standby).
or line 2.
1)Pick up the
handset.
2)Press line 1 2)Listen for
or line 2.
3)Listen for the
dial tone.
4)Press
1)Press line 1 1)Press
or line 2. line 1 or
line 2.
2)Listen for
the dial
the dial
tone.
3)Press
REDIAL/
PAUSE.
OR
tone.
3)Press
REDIAL/P.
REDIAL/
PAUSE.
To
redial
OR
Press
1)Pick up the
handset.
2)Press
REDIAL/
PAUSE, then
press line 1
or line 2.
REDIAL/
PAUSE, then
press line 1 or
line 2.
ADJUSTING THE RINGER AND
EARPIECE/SPEAKER VOLUME
Ringer Volume
When the phone is in standby mode,
pressing the SELECT/VOL/RING on the
handset selects the handset ringer volume.
There are three (High, Low, Off) ringer
volume settings. Press the SELECT/VOL/
RING key to listen to volume levels.
The phone keeps the last ringer volume
setting selected.
Earpiece Volume
The handset earpiece volume settings
(Low, Medium, High and Maximum) can
only be adjusted during a call. Press
SELECT/VOL/RING repeatedly to select Low,
Medium, High or Maximum. When you hang
up, the phone keeps the last volume setting
selected.
13
Base Ringer Volume
The ringer control for the base of your
cordless phone allows you turn the ringer
OFF or to select LO/HI volume for each line
1 or line 2.
Base Speaker Volume
To control the speaker volume of the base,
press VOLUME/ or VOLUME/ during a call.
There are 7 speaker volume levels.
REDIAL
Ô NOTES Ô
Redial
The cordless phone has
two independent last
number redial memories;
one in the handset, the
other in the base.
The REDIAL/PAUSE key redials the last
number dialed. The redialed number can be
up to 32 digits long. Ô
Handset
Press line 1 or line 2, then press REDIAL/
PAUSE.
Tone Dialing Switch-over
•
The tone feature only
applies when the dial
mode is set to pulse.
Or press REDIAL/PAUSE, then press line 1 or
line 2.
•
This special number can
be stored in a memory
location. This is referred
to as Chain Dialing.
Base
Press line 1 or line 2, then press REDIAL/P.
If any key is pressed before REDIAL/P, the
last number will not redial.
TONE DIALING SWITCH-OVER
Some telephone companies use equipment
that requires pulse dialing (sometimes
referred to as rotary dialing). If you need to
enter tone dialing digits, you can switch-
over to tone dialing during the call. For
example, entering your bank account
number after you have called your bank.Ô
Initially make your call with the pulse dialing
mode. Once your call connects, press
/
tone/< . Enter the desired number. These
14
digits will be sent as tone dialing. Once the
call ends, the tone mode is canceled and
pulse dialing mode resumes. Ô
TRAVELING OUT-OF-RANGE
During a call, as you begin to move your
handset too far from your base unit, noise
increases. If you pass the range limits of the
base unit, your call will terminate within 60
seconds.
SELECTING A DIFFERENT
CHANNEL
If you encounter interference while using your
phone, you can manually change the phone’s
channel for clear operation. This function
works only when the phone is in use.
The CHANNEL on the handset allows you to
choose between 20 different channels.
During the course of a conversation, if you
hear static or noise which makes it difficult
to hear, press CHANNEL. The phone
changes to a different channel.
USING THE PAGE FEATURE
1. To locate the handset (when it is off the
base), press INTERCOM on the base.
The handset beeps for 60 seconds.
2. Press any key on the handset to
connect to the base.
3. Press INTERCOM, /INTCM, or return
the handset to the base to return to
standby.
FLASH AND CALL WAITING
If you have “Call Waiting” service and a call
waiting tone sounds while you are on a call,
15
press DELETE/FLASH to accept the waiting
call. There is a short pause, then you will
hear the new caller.
To return to the original caller, press
DELETE/FLASH again. Ô
Ô NOTE Ô
Flash and Call Waiting
•
The flash feature does
not function when line 1
and line 2 are on a
USING THE SPEAKERPHONE
You may use the phone as a speakerphone
to answer calls by pressing the line 1 or line
2 button on the base. To hang up, press line
1 or line 2 again.
conference call. (See “3-
Way Conferencing” and
“4-Way Conferencing”,
pages 19 and 20).
•
You must subscribe
through your local
telephone company to
receive Call Waiting
Service.
The base microphone is located under the
phone. Position yourself as near to the base
as possible and speak clearly.
If the handset is on the base, you may use
either the base keypad or memory dialing to
place a call.
Answering a Call from the
Handset
If you set the handset to
Auto Talk On, and the
handset is on the base, just
pick up the handset and
speak.
Each line setting is
independent for this
feature.
ANSWERING A CALL FROM
THE BASE
1. The base rings. The corresponding
line 1 LED on the base flashes.
2. Press line 1 and speak.
3. When you finish the call, press line 1 to
hang up.
ANSWERING A CALL FROM
THE HANDSET
(Call) Line 1
1. The handset rings and
appears.
2. Press line 1 to answer your call. Ô
3. When you finish the call, press line 1 on
the handset, or return the handset to
the base.
16
MAKING A CALL FROM THE
BASE
1. Press line 1.
2. Dial the number on the keypad, or use
one of the memory features. (See
“Making Calls with Memory Dialing” on
page 29.)
3. When you finish the call, press line 1 to
hang up.
MAKING A CALL FROM THE
HANDSET
Dialing from Talk Mode
1. Pick up the handset.
2. Press line 1.
Dial the number on the keypad. Or use
one of the memory features. (See
“Making Calls with Memory Dialing” on
page 29.)
You have to use number keys when you
use memory key.
3. When you finish the call, press line 1 or,
return the handset to the base.
Dialing from Standby Mode
To call a number while the handset is in
standby mode, dial the number on the
keypad, or use one of the memory features.
Press line 1. (See “Making Calls with
Memory Dialing” on page 29.) Ô
Ô NOTE Ô
If a line is in use, or a phone
In Use
is off the hook, “
Line 1 Line 2
(or
)”
appears on the display.
PLACING A CALL ON HOLD
Use either the keypad on the handset or the
keypad on the base.
17
1. To place line 1 on hold at the base,
press HOLD. The line 1 red LED
flashes.
2. To place line 1 on hold at the handset,
press CID/MENU/HOLD.
3. To pick up the call that is holding, press
line 1 on the base or handset.
USING THE SPEAKERPHONE
MUTE FEATURE
Your cordless phone allows you to mute
your conversation from the base. This
prevents the party you are speaking to from
hearing what you, or someone else in the
room, is saying.
For example, to use this privacy feature
while using line 1.
1. Press MUTE.
The line 1 LED flashes green.
You can hear the party on line 1, but
they cannot hear you.
2. When you are ready to continue your
conversation with the party on line 1,
press MUTE or line 1 again. The line 1
LED stops flashing.
2-LINE FEATURES
2-LINE OPERATION
The handset and the base can be used on
separate telephone lines at the same time.
For example, if the handset is on a call
using line 1, you can make, or receive calls
at the base on line 2. Ô
Ô NOTE Ô
When you attempt to make
a call, the cordless phone
informs you if a line is
currently in use.
18
The line 1 LED on the base flashes green to
indicate line 1 is in use at the handset.
When line 1 is in use at the base, the LCD
(Base) Line 1
screen displays
.
Extension In Use
The Extension in use feature prevents
accidental interruption of ongoing telephone
conversations.
If you attempt to make a call and another
phone is in use on line 1, the handset LCD
indicates an extension is in use. (The line 1
LED at the base blinks.)
3-WAY CONFERENCING
This feature lets you add a third party to
your conversation from either the handset
or the base.
For example, to add a party to the current
call on line 1 at the base:
1. Press HOLD to place the caller on hold.
The line 1 LED turns from green to
flashing red.
2. Press line 2.
3. Dial the number of the person you want
to add to the conversation.
Ô NOTES Ô
When the person answers, you can
speak privately before bringing the
original caller back on the line.
•
•
The flash feature does
not function when the
phone is in conference
mode.
4. Press conf to bring the original call
back on line.The line 1 and line 2 LEDs
are green. Ô
If you want to join a
conversation on an
extension currently in
use, press line 1 or
line 2.
If the third person’s number is busy or
doesn’t answer, press line 2 to hang up.
19
Return to the original call by pressing
line 1.
5. To remove either caller from your
conversation, ask one of the parties to
hang up. Press the corresponding line
button to end the call.
Follow steps 1-5 to conference using
the handset. When you return the
handset to the base, all calls are
disconnected.
4-WAY CONFERENCING
A fourth person, at either the handset or the
base, may be added to conference call.
For example, to add a fourth party at the
handset to an ongoing conference call at
the base:
1. Press HOLD. The line 1 and line 2 LEDs
flash red.
2. Press INTERCOM on the base to
contact the handset.
3. Press /INTCM on the handset.
Speak to answer the page.
4. Press conf on the base or /CONF at
the handset to bring the party at the
handset in on the call. The line 1 and
line 2 LEDs are green.
5. To remove either caller from your
conversation, ask one of the parties to
hang up.
Press the corresponding line button to
end the call.
20
USING YOUR CORDLESS
PHONE INTERCOM
Paging from the Base to Handset
1. Press INTERCOM on the base.
The handset beeps. (If no answer,
press INTERCOM on the base again to
disconnect.)
2. Press any key on the handset.
Speak into the mouthpiece to answer
the page.
3. To turn off the intercom, press
INTERCOM on the base or /INTCM on
the handset.
Paging from the Handset to Base
1. Press /INTCM on the handset. (If no
answer, press /INTCM on the handset
to disconnect.)
2. At the base, press INTERCOM.
Speak into the base microphone to
answer the page.
3. To turn off the intercom, press
INTERCOM at the base or /INTCM on
the handset.
TRANSFERRING CALLS
1. To transfer a call from the base or
handset, press HOLD or CID/MENU/
HOLD. The line 1 LED flashes red.
2. Press INTERCOM or /INTCM.
3. Answer the transferred call by pressing
/INTCM or INTERCOM. On the base
the CHARGE/IN USE LED illuminates.
21
You may then announce the call with
the intercom.
4. To speak to the caller, press line 1.
If no one is available to take the call,
you can return to the caller by pressing
line 1 to take a message or complete
the call.
SETTING MENU
OPTIONS
There are four setup options available. They
are Caller ID options [Auto Talk, CIDCW
(Caller ID on Call Waiting), Area Code], and
Language. See “To Enter Your Area Code”
on page 24.
Auto Talk allows you to answer the phone
without pressing the line 1 key or the line 2
key. If the phone rings when Auto Talk is on,
simply remove the handset from the base
and the phone automatically answers the
call. Or if the handset is not on the base,
press any key on the handset to answer the
call. If the phone rings when Auto Talk is off,
you must press the line 1 key or the line 2
key to answer the call.
Caller ID on Call Waiting (CIDCW) performs
the same as regular Caller ID on a call
waiting number. You must subscribe to
CIDCW from your phone company in order
to use this feature.
To Change Your Auto Talk and
CIDCW:
1. When the phone is in the standby
mode, press and hold the CID/MENU/
HOLD key until the Caller ID setting
screen appears.
22
2. Press the /INTCM key or the /CONF
Line 1 Line 2
”.
key to select “
” or “
3. Press #/>.
4. Press the /INTCM key or the /CONF
key to move the cursor to the selection
that you would like to change. Press the
SELECT/VOL/RING key to toggle
On
Off
”.
between “ ” and “
5. After you have made your selections,
press the CID/MENU/HOLD key or return
the handset to the base. Ô
Choosing the Dialing Mode
Most phone systems use tone dialing which
sends DTMF tones through the phone lines.
However some phone systems still use pulse
dialing such as in rural areas. The default
setting is tone dialing. Depending on your
dialing system, set the mode as follows: Ô
Ô NOTES Ô
To Change Your Auto
Talk and CIDCW:
Please return the handset
to the base after you set
CIDCW.
1. Press and hold the FLASH key on the
base until you hear a confirmation tone.
Choosing the Dialing
Mode
Make sure your battery
pack is fully charged before
setting Caller ID options.
2. To set the dial mode for pulse dialing,
press # on the base. Or to set the dial
mode for tone dialing, press /tone on
the base. A confirmation tone sounds
to indicate the setting is complete.
• If you are not sure of your dialing
system, set for tone dialing. Make a trial
call. If the call connects, leave the
setting as is, otherwise set for pulse
dialing.
• If your phone dialing system requires
pulse dialing and you need to send
DTMF tones for certain situations
during a call, you may "switch-over" to
tone dialing. (See “Tone Dialing Switch-
over” on page 14.)
23
To Enter Your Area Code
If you enter a 3-digit area code number in
Area Code
the “
” option, your local area
code does not appear in the Caller ID
messages. Do not program this option, if
your calling area requires 10-digit dialing.
When reviewing Caller ID messages, you
will see only the local seven digit number.
For calls received from outside your local
area code, you will see a full 10-digit
number. Ô
Ô NOTE Ô
When the area code has
already been stored in
memory, the stored area
code will be displayed. To
change it, use the DELETE/
FLASH and number
1. When the phone is in the standby
mode, press and hold CID/MENU/HOLD
until the Caller ID setting screen
appears.
keypad to enter the new
area code.
2. Press /INTCMor /CONF to select
Line 1 Line 2
”.
“
” or “
3. Press #/>.
4. Press /INTCM or /CONF to select
Then press SELECT/VOL/
RING. To complete the
setting, press CID/MENU/
HOLD or return the handset
to the base unit.
Area Code
“
”.
5. Press SELECT/VOL/RING.
6. Use the dial buttons (0 - 9) to enter the
3-digit area code.
7. Press SELECT/VOL/RING. A tone
sounds and the displayed area code is
entered.
8. Press CID/MENU/HOLD to complete the
setting. Or return the handset to the
base unit. The handset returns to
standby mode. Ô
Setting the Language
1. When the phone is in the standby
mode, press and hold CID/MENU/HOLD.
24
2. Press /CONF twice to select
Language
“
”.
3. Press SELECT/VOL/RING to toggle
Eng
between “
”(English) and
Fr.”(French) for each setting.
“
4. Press CID/MENU/HOLD or return the
handset to the base unit.
The handset returns to the standby
mode.
MEMORY FEATURES
STORING PHONE NUMBERS
AND NAMES
Memory Dialing allows you to dial a number
using just a few key presses.
Your cordless phone stores up to 30 names/
numbers in the handset plus 10 numbers in
the base. Memory locations are shared by
both lines. Ô
Ô NOTE Ô
Whenever you are using a
menu screen, you must
press a key within 30
With the Handset
1. Pick up the handset from the base.
seconds or the phone will
return to standby. You may
also press MEMORY to exit
a memory menu at anytime.
2. Press MEMORY.
3. Use the /INTCM and /CONF, or
number keypad (01-30), to choose the
memory location to store a name/
number.
4. Press SELECT/VOL/RING.
5. Press SELECT/VOL/RING.
6. Entering a stored name - “Use the
number keys, /tone/<, #/>, or DELETE/
FLASH to edit the name. (See “If you
25
make a mistake while entering a name”
on page 27.)
To edit only the phone number, skip this
step.
7. When you have finished entering a
name, press SELECT/VOL/RING.
The cursor flashes, indicating that the
display is ready for a number to be
entered.
8. Enter the phone number with the
number keypad. If you want to change
the entered number, press DELETE/
FLASH and the cursor will move one
space to the left and delete that
number.
When entering numbers, you may
press REDIAL/PAUSE to enter a pause
in the dialing sequence. The display
P
shows a “ ”.
Ô NOTE Ô
The phone number cannot exceed 20
Each pause counts as one
digit and represents a two
second delay of time
between the digits as they
are sent. The pause feature
is useful for long distance
calling, credit card dialing,
or any other dialing
digits. Ô
9. When you have finished entering a
name/number, press SELECT/VOL/
RING.
You will hear a confirmation tone.
sequence requiring a pause
between digits.
With the Base
1. Press MEMORY. The CHARGE/IN USE
LED blinks.
2. Dial the number you wish to store.
The phone number cannot exceed 20
digits.
26
3. Press MEMORY. Enter the memory
location number (0 - 9) on the keypad.
The CHARGE/IN USE LED is no longer
illuminated. A confirmation tone
indicates the number is stored.
STEPS FOR ENTERING NAMES
AND SPECIAL CHARACTERS
Refer to the letters on the number keys to
select the desired characters.
Ô NOTE Ô
If the next character uses
the same number key, you
must press #/> to move the
cursor over. Otherwise the
next time you press the
number key, it changes the
character that was
With each press of a numeric key, the
displayed character appears in the following
order: Upper case letters first, lower case
letters next and finally the number
corresponding to the key. Ô
If you make a mistake while
entering a name
previously set.
Use the /tone/< or #/> key to move the
cursor to the incorrect character.
Press DELETE/FLASH to erase the wrong
character, then enter the correct character.
To delete all characters, press and hold
DELETE/FLASH.
For example, to enter Movies.
1. Pick up the handset. Press MEMORY.
2. Enter a number or press the /INTCM
or /CONF key to select a memory
location.
3. Press SELECT/VOL/RING.
4. Press SELECT/VOL/RING. (When there
is information already stored in the
Edit
selected memory location, ¨
MemoryXX
¨ is displayed. See page 30
27
for information on “Editing a Stored
Name and/or Phone Number”.)
5. Press 6 then press #/>to move the
cursor to the right.
6. Press 6 six times.
7. Press 8 six times.
8. Press 4 six times.
9. Press 3 five times.
10. Press 7 eight times.
11. When finished, press SELECT/VOL/
RING.
To continue to store the telephone number,
proceed to step 8 on page 26.
28
MAKING CALLS WITH
MEMORY DIALING
Ô NOTES Ô
Follow the steps below to dial a number
using a programmed memory location: Ô
•
•
To exit the memory
function without dialing
press MEMORY. The
handset returns to
standby.
When reviewing memory
location you must press
a key within 30 seconds
or the phone will return
to standby.
With the Handset
1. Press MEMORY. The handset displays
your programmed memory locations.
Ô
2. Press /INTCM and /CONF, or enter
the number (01-30) to select the
memory location you would like to dial.
3. Press line 1 or line 2.
The number dials.
With the Base
1. Press line 1 or line 2.
The line’s LED illuminates.
2. Press MEMORY. Enter the memory
location number (0-9), to dial the
number.
CHAIN DIALING
The 30 memory locations on the handset
are not limited to phone numbers.
You may want to store in memory a group of
numbers (up to 20 digits) that you need to
enter once your call connects. This is
referred to as Chain Dialing.
An example of this is a bank account
number. Once you have called your bank,
when you are prompted to enter the account
number, simply press MEMORY and then
select the location where the special
number has been stored.
29
Store your special number in memory as
you would a phone number.
(See “Storing Phone Numbers and Names”
on page 25.)
Enter a “pause” in the sequence as
necessary. A “pause” counts as one digit
and represents a two second delay in time
between digits as they are sent.
EDITING A STORED NAME
AND/OR PHONE NUMBER
To edit a number you have stored in the
handset.
Ô NOTES Ô
1. Pick up the handset from the base.
•
•
When reviewing memory
location, you must press
a key within 30 seconds
or the phone will return
to standby.
2. Press MEMORY. The display shows the
Select Memory
“ ” screen and any
saved names/numbers. Ô
3. Use the /INTCM and /CONF, or
number keypad, to select the memory
location (01-30) you would like to edit.
Go Back
If you select “
no changes are made
and the handset shows
Select Memory
”,
the “
screen.
”
4. Press SELECT/VOL/RING.
5. Press SELECT/VOL/RING. The display
shows the memory location you have
selected.Ô
6. Press SELECT/VOL/RING again to enter
Edit Memory
the “ ” mode.
7. A cursor flashes indicating that the
display is ready to edit the name.
8. Entering a stored name - “Use the
number keys, /tone/<, #/>, or DELETE/
FLASH to edit the name. (See page 28)
To edit only the phone number, skip this
step.”
30
9. Press SELECT/VOL/RING.
A cursor flashes indicating that the
display is ready for the number to be
edited.
10. Enter the phone number with the
number keypad (direct entry).
Press DELETE/FLASH to remove any
unwanted character.
Press and hold DELETE/FLASH to clear
the entire number.
11. Press SELECT/VOL/RING. If you
changed either name or phone number,
a confirmation display shows up.
If it is correct, press /INTCM and press
the SELECT/VOL/RING key again.You
will hear a confirmation tone.
Select
12. The display then returns to the “
Memory
” screen.You may select
another number to edit (return to step
3) or press MEMORY to return to
standby. To edit a number stored in the
base, repeat the steps for storing
numbers in the base. (See page 26.)
This will simply overwrite the number
that was previously stored in the
location.
ERASING A STORED NAME
AND PHONE NUMBER
With the Handset
1. Pick up the handset from the base.
2. Press MEMORY . The handset shows
Select Memory
the “
” screen with
saved name/numbers displayed.
31
3. Use the /INTCM and /CONF, or
number keypad (01-30), to select the
memory location you would like to
delete.
4. Press SELECT/VOL/RING.
5. Press SELECT/VOL/RING.
Ô NOTES Ô
Erasing a Stored Name
and Phone Number
6. Use the /CONF to move the cursor to
Delete MemoryXX
“ ”. Ô
7. Press SELECT/VOL/RING.
Go Back
“,
•
If you select “
no changes are made
and the handset shows
Select Memory
8. Use the /INTCM to move the cursor to
Yes
“ ”. Ô
the “
screen.
If you select “ “, no
“
9. Press SELECT/VOL/RING or DELETE/
No
•
FLASH.
changes are made, the
handset shows the
There is a confirmation tone.
Select Memory
“
”
screen.
Caller ID Features
Select
10. The display then returns to the “
Memory
” screen.You may select
•
If you answer a call
before the Caller ID
message is received
(Example : before the
second ring), the Caller
ID message will not
appear.
another number to delete (return to
step 3) or you may press MEMORY to
return to standby.
With the Base
1. Press MEMORY.
•
When the call is received
via a telephone
2. Press MEMORY again. Enter the
memory location (0-9) of the number
you wish to delete.
company that does not
offer Caller ID service,
the caller’s phone
number and name does
not appear. (This
A confirmation tone indicates the
number has been deleted.
includes international
calls.)
CALLER ID FEATURES
•
When the call is via a
private branch exchange
(PBX), the caller’s phone
number and name may
not appear.
CALLER ID
You must subscribe to Caller ID from your
phone company to use this feature. Ô
32
When the telephone rings, the Caller ID
feature allows you to review caller’s name
and phone number on the display before
you answer the phone. At the second ring,
the handset displays the phone number of
the incoming call, the name. If your Caller
ID service is number only, the name does
not appear on the second line.
If a name or number is not available, the
display shows a message such as
Incomplete Data Private Number
“ “, “ “,
Private Name Unknown Name
“ “, “ “, etc.
Additionally, you can dial the displayed
number and store the information for
memory dialing. Make sure you have turned
on the Caller ID/Call Waiting feature (See
page 22).
WHEN THE TELEPHONE RINGS
When the Caller ID message is received,
the display shows the caller’s phone
number along with the name. The incoming
call information is stored in the Caller ID
record. If the Caller ID service includes the
caller’s name, the caller’s name appears on
the display (up to 15 letters).
VIEWING THE CALLER ID
MESSAGE LIST
The Caller ID list stores information for up to
80 incoming calls - even unanswered calls.
Ô NOTES Ô
If you have no Caller ID
name/numbers, then the
•
•
To review your Caller ID names/numbers,
follow the steps below:
00
total is shown as “ ”.
Once a Caller ID
message has been
viewed, it is no longer
considered a new
message.
1. Press CID/MENU/HOLD. Ô
Line 1
2. Use /tone/< or #/> to select “
”
Line 2
or “ ” for Caller ID.
33
3. Press /CONF to see the next
message.
Or press /INTCM to see previous
message. Ô
4. Press CID/MENU/HOLD to return to
standby.
USING THE CALLER ID LIST
Calling a Caller ID name/number
You can place a call from the Caller ID list.
The cordless phone stores up to 80
messages.
Ô NOTES Ô
•
•
In Caller ID operation, if
no key is pressed for
more than 30 seconds,
an error tone sounds
and the telephone
returns to the standby
mode.
1. Press CID/MENU/HOLD. The Caller ID
summary screen shows the number of
new callers and total number of calls.
Ô
If a call comes in via a
telephone system that
does not offer Caller ID
service, no information is
stored.
Line 1
2. Use /tone/< or #/> to select “
”
Line 2
or “ ” Caller ID.
3. Press /CONF to scan forward.
Press /INTCM to scan backwards
through the list.
•
•
Each message can be
up to 15 characters for
the phone number and
the name.
4. Select the name/number that you
would like to dial.
The number of calls from
the same Caller ID
appears next to the
received time.
5. Press line 1 or line 2. The number
automatically dials.
Once you view the new
calls, the number will be
cleared and
Long Distance Calls and Area
Code Setting/Cancellation
Pressing 1 while the incoming Caller ID
disappeared.
information is displayed (in step 3) will place
1
the prefix “ ” in the display to setup for a
long distance call.
34
Pressing 3 will set or cancel an area code
setting.
Storing a Caller ID Number in a
Memory Location
1. Press CID/MENU/HOLD. The Caller ID
summary screen shows the number of
new callers and total number of calls.
Line 1
2. Use /tone/< or #/> to select “
”
Line 2
or “ ” Caller ID.
3. Press /INTCM or /CONF to find the
name/number that you would like to
store.
4. Press MEMORY to store the selected
message.
Select Memory
5. The “
” screen appears.
Use the /INTCM and /CONF, or enter
the number (01-30) to select a blank
memory location where you would like
to store the number.
(If you want to replace an existing
number with the Caller ID number, skip
to step 7).
6. Press SELECT/VOL/RING. A
confirmation tone sounds. The number
is programmed.
7. If you choose to replace an existing
number with the Caller ID number,
press SELECT/VOL/RING.
8. Use the /INTCM to move the cursor to
Yes
“
”. Press SELECT/VOL/RING.
A confirmation tone sounds and the
number is programmed. Ô
Ô NOTE Ô
No
If you select “ ”, then the
Caller ID screen returns.
35
DELETING INFORMATION
FROM THE CALLER ID LIST
The cordless phone stores up to 80
messages. If the phone receives the 81st
message for each line, the oldest one in the
list is automatically deleted. Caller ID data
can also be deleted manually.
Deleting a Caller ID Message
To delete a single Caller ID message, follow
the steps below.
1. Press CID/MENU/HOLD. The Caller ID
summary screen shows the number of
new callers and total number of calls.
Line 1
2. Use /tone/< or #/> to select “
“
Line 2
or “ “ Caller ID.
3. Press /INTCM or /CONF to find the
name/number.
4. Press DELETE/FLASH.
Ô NOTES Ô
Delete
While using the “
5. Press SELECT/VOL/RING or DELETE/
FLASH. A confirmation tone sounds.
The Caller ID screen returns with the
next name/number displayed. Ô
•
•
All?
“ or “
Delete
Message?
“ screen if no
key is pressed within 30
seconds, an error tone
sounds and the
telephone returns to
standby.
No
If you select “ ”, the Caller ID screen
returns.
6. Press CID/MENU/HOLD to return to
If you get an incoming
call or page, the deleting
operation is canceled so
you can answer the call
or page.
standby.
Deleting All Caller ID Name/
Numbers
To delete all of your Caller ID messages,
follow the steps below.
1. Press CID/MENU/HOLD. the Caller ID
summary screen shows the number of
new callers and total number of calls.
36
Line 1
2. Use /tone/< or #/> to select “ “.
3. Press DELETE/FLASH to delete name/
numbers on line 1.
4. Use the /INTCM to move the cursor to
Yes
“
“.
5. Press DELETE/FLASH or SELECT/VOL/
RING. A confirmation tone sounds.
6. Repeat steps 3 through 5 for line 2.
All your Caller ID messages are
deleted.
USING CIDCW (CALLER ID
ON CALL WAITING)
1. During a call, when you hear the Caller
ID tone, check the handset display for
the name and the number of the
incoming call.
2. Press DELETE/FLASH to accept the
incoming call. See “Flash and Call
Waiting” on page 15.
USING A HEADSET
Ô NOTES Ô
You can make or answer calls with hands-
free convenience using an optional headset
that has a 3/32-inch (2.5-mm) plug.
RadioShack has a variety of headsets
available.
•
•
If you place the handset
on the base to recharge
it while the headset is
connected, be sure the
handset seats propely.
To connect the headset, gently flip open the
rubber headset jack cover on the side of the
handset, then insert the headset’s plug into
the jack. Ô
You can use a handset
holder (available from
your local RadioShack
store) to hang the
handset on your belt for
greater convenience
when using a headset.
Connecting a headset disconnects the
handset’s earpiece and microphone.
37
SELECT/VOL/RING on the handset also
controls the headset’s volume.
With a headset connected, you can make or
answer calls as usual using the keys on the
handset.
When you finish using the headset,
disconnect it from the handset and close the
rubber cover to protect the jack.
38
TROUBLESHOOTING
If your phone is not performing to your expectations, please try these
simple steps first.
Symptom
Suggestion
• Make sure the AC adapter is plugged into the base unit
and wall outlet.
The CHARGE/IN USE
LED won’t light when • Make sure the handset is properly seated on the base
the handset is placed
on the base unit.
unit.
• Make sure the charging contacts on the handset and
base unit are clean.
• Press CHANNEL during a call to help eliminate
background noise.
• Make sure that the base unit antenna is in a vertical
position.
The audio sounds
weak and/or scratchy. • Move the handset and/or base unit to a different
location away from metal objects or appliances and try
again.
• Make sure that you are not too far from the base.
• Check both ends of the base unit telephone line cord.
• Make sure the AC adapter is plugged into the base unit
and wall outlet.
• Disconnect the AC adapter for a few minutes, then
reconnect it.
Can’t make or receive
calls.
• Change the digital security code (See page 11).
• Make sure line 1 or line 2 is pressed.
• The battery pack may be weak. Charge the handset on
the base unit for more than 15 hours.
The handset doesn’t
• The handset may be too far away from the base unit.
ring or receive a page. • Place the base unit away from appliances or metal
objects.
• Change the digital security code (See page 11).
• Keep the handset away from microwave ovens,
computers, remote control toys, wireless microphones,
Severe noise
interference.
alarm systems, intercoms, room monitors, fluorescent
lights, and electrical appliances.
• Move to another location or turn off the source of
interference.
• The handset was picked up before the second ring.
• The call was placed through a switchboard.
• Call your local telephone company to verify your Caller
ID service is
The Caller ID/CIDCW
does not display.
On
• Make sure that the CIDCW option is set to “ ”.
39
If you still have problems, disconnect the
phone. If other phones on the same line
work properly, the fault is in this phone or its
installation. Check the REN (See “FCC
Statement”). If you cannot find the problem,
take the phone to your local RadioShack
store for assistance.
CARE
Keep the phone dry; if it gets wet, wipe it dry
immediately. Use and store the phone only
in normal temperature environments.
Handle the phone carefully; do not drop it.
Keep the phone away from dust and dirt,
and wipe it with a damp cloth occasionally
to keep it looking new.
SERVICE AND REPAIR
If your phone is not performing as it should,
take it to your local RadioShack store for
assistance. To locate your nearest
RadioShack, use the store locator feature
on RadioShack's website
Shack (843-7422) and follow the menu
options. Modifying or tampering with the
phone's internal components can cause a
malfunction and might invalidate its
warranty, and void your FCC authorization
to operate it.
FCC STATEMENT
Your telephone compiles with Part 68 of the
FCC Rules.Upon request, you must provide
the phone’s FCC registration number and
REN to your phone company. These
numbers are on the base unit.
Your phone is not intended to be used with
party-line systems. Connection to party line
service is subject to state tariffs. Contact the
40
state public utility commission, public
service commission, or corporation
commission for information. Ô
Ô NOTE Ô
You must not connect your
phone to:
We have designed your phone to conform
to federal regulations, and you can connect
it to most telephone lines. However, each
phone (and each device, such as a
telephone or answering machine) that you
connect to the telephone line draws power
from the telephone line. We refer to this
power draw as the device’s ringer
•
•
coin-operated systems
most electronic key
telephone systems
equivalence number, or REN on the back of
your phone.
If you use more than one phone or other
device on the line, add up all of the RENs. If
the total is more than five (three in rural
areas), your telephones might not ring. If
ringer operation is impaired, remove a
device from the line.
In the unlikely event that your phone causes
problems on the phone line, the phone
company can temporarily discontinue your
service. If this happens, the phone company
attempts to notify you in advance. If
advance notice is not practical, the phone
company notifies you as soon as possible
and advises you of your right to file a
complaint with the FCC.
Also, the phone company can make
changes to its lines, equipment, operations,
or procedures that could affect the operation
of this phone. The telephone company
notifies you of these changes in advance, so
you can take the necessary steps to prevent
interruption of your telephone service.
SURGE PROECTION
Your telephone has built-in protection
circuits to reduce the risk of damage from
surges in telephone line and power line
current. These protection circuits meet or
exceed the FCC requirements. However,
41
lightning striking the telephone or power
lines can damage your telephone.
Lightning damage is not common.
Nevertheless, if you live in an area that has
severe electrical storms, we suggest that you
unplug your phone when storms approach to
reduce the possibility of damage.
42
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and
workmanship under normal use for one (1) year from the date of purchase from RadioShack
company-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS
PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IM-
PLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRIT-
TEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY
OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE
CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT
OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIM-
ITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA,
PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POS-
SIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages, so the above limitations or exclusions may
not apply to you.
In the event of a product defect during the warranty period, take the product and the Ra-
dioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will,
at its option, unless otherwise provided by law: (a) correct the defect by product repair with-
out charge for parts and labor; (b) replace the product with one of the same or similar design;
or (c) refund the purchase price. All replaced parts and products, and products on which a re-
fund is made, become the property of RadioShack. New or reconditioned parts and products
may be used in the performance of warranty service. Repaired or replaced parts and prod-
ucts are warranted for the remainder of the original warranty period. You will be charged for
repair or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God,
abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper
installation or maintenance, alteration, lightning or other incidence of excess voltage or cur-
rent; (b) any repairs other than those provided by a RadioShack Authorized Service Facility;
(c) consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, ship-
ping or insurance costs; or (f) costs of product removal, installation, set-up service adjust-
ment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
12/99
43-3701
UPZZ01014BZ
04A03
Printed in China
RadioShack Corporation
Fort Worth, Texas 76102
|
