Roadmaster Car Speaker RS460 User Guide

RS460  
Frequently Asked Questions  
Installation  
4” x 6” Three-Way Speaker  
What if there is no sound?  
1. Your stereo may have a blown fuse. Replace fuse with the same amperage and  
style.  
2. You may have improper wiring. Refer to the wiring guide that came with your stereo/  
amplier. Check all wires for a secure connection.  
Location  
Dear Customer,  
CONGRATULATIONS.  
If you are installing the RS460 speakers to upgrade/replace your existing speakers, re-  
move the existing speakers from your vehicle, disconnect the speaker wires and mark  
the polarity. Place the RS460 speakers in the location you selected in your vehicle and  
connect the existing speaker wires. Make sure to keep the polarity of the speakers and  
wires correct (positive wire to positive speaker terminal and negative or ground wire to  
negative terminal)  
The RS460 4” x 6” 3-way speakers, when used as described, will give you years of  
dependable service in your car, truck, RV or mini-van. We have taken numerous mea-  
sures in quality control to ensure that your product arrives in top condition, and will  
perform to your satisfaction. In the rare event that your RS460 4” x 6” 3-way speakers  
contain a damaged or missing item, does not perform as specied, requires warranty  
service, or you have an installation problem, DO NOT RETURN THIS PRODUCT TO  
THE STORE. PLEASE CALL OUR TOLL FREE NUMBER FROM THE U.S.A. AND CAN-  
ADA 1-800-445-1797 and ask to speak with a member of our technical service team,  
or submit your questions by E-Mail to [email protected] and a member  
of our technical service team will respond by E-Mail to your questions. Our in-house  
technical service team will expedite delivery of your part, advise you on installation,  
or help troubleshoot a problem with you. If your product needs warranty service, our  
technical service team representative will help you obtain the fastest remedy possible  
under the warranty.  
What if the sound volume is low?  
Your stereo may not have enough power, you may have to install an amplier to  
drive the speakers  
Speaker Depth  
25/" or 61/ cm  
8
2
Before you install your speakers you must make sure you  
have enough depth/space behind the mounting surface.  
You do not want the back of the speaker magnet to touch any part  
of your vehicle, or interfere with the operation or function of any  
component in your vehicle. (ie. windows or trunk lid)  
Why do I have a whining noise coming from the speakers?  
You may have poor ltering of your alternator. If that is the case then you  
may need to add an alternator lter to the power lead.  
Why do I have odd sounding noises coming from the speakers?  
You may have corroded battery terminals and/or a weak battery. If the terminals on  
the battery are corroded clean them, then check the sound. If the sound system is still  
making noises check battery strength. If it is low, recharge or replace the battery.  
Before mounting the speakers in a precut hole, use the template to check  
that the holes for the speaker and the screws will line up correctly.  
Why does the speaker have sound coming from one channel only?  
First make sure the balance control is set correctly. If the balance is set correctly  
your stereo may be defective or the speaker may be defective. To troubleshoot  
this problem you MUST change both positive and negative leads of each channel with  
the positive and negative leads of the opposite channel, if the same speaker has no  
sound then the speaker is no good, if the opposite speaker has no sound then your  
stereo may be defective.  
Parts & Specications  
Mounting  
• 4” x 6” Polypropylene Coated Paper Cones  
• 6 Oz. Magnet  
• Foam Rubber Surrounds  
• 100 Watts Maximum Peak Power per Pair  
• 20 Watts RMS Power per Pair  
• 115 - 20,000 Hz Frequency Response  
• Bridgeless 1.5” Midrange speakers  
• .5” Dome Tweeters  
You should only mount your speakers in factory precut holes. We  
DO NOT recommend that you cut holes for mounting the speakers. If  
there are no factory precut holes consider having the speakers pro-  
fessionally installed.  
GIVE US A CALL, WE'LL HELP YOU INSTALL.  
The small hole of  
the spring nut is  
on this side of panel  
PLEASE DO NOT RETURN PRODUCT TO STORE.  
Visit us on the WEB  
2 Speakers  
INTERIOR PANEL  
1. Connect the speaker wires to  
the speaker. Maintain polarity by  
connecting the positive wire to the  
positive speaker terminal, and the  
negative wire to negative speaker  
terminal.  
For Information and Technical Assistance,  
Call Toll-Free in U.S.A. and Canada.  
• Quick Connect Terminals  
1-800-445-1797  
SPRING NUT  
2. Slip the supplied spring nuts into  
place and align the holes.  
2 Grills  
8 Screws  
8 Spring Nuts  
Limited Warranty  
VIRTUAL REALITY SOUND LABS® products are designed and manufactured to provide a high level of trouble-free per-  
formance. VIRTUAL REALITY SOUND LABS® warrants, to the original purchaser, that its products are free from defects in  
material and workmanship for 30 days from the date of original purchase. As part of our commitment to product excellence,  
VIRTUAL REALITY SOUND LABS® and/or its afliates routinely improve the designs, materials or production methods of  
its existing products. Because it is impractical to publicize all changes in every product, we reserve the right to make such  
changes without notice.  
Tools Needed To Install  
SPEAKER  
WIRE  
SPEAKER GRILL  
Spring Nut  
• Marker/Pen  
CONDITIONS OF WARRANTY:  
• Nail Set/Center Punch  
• Phillips Screwdriver  
If during the 30 day warranty period your new product is found to be defective, VIRTUAL REALITY SOUND LABS® will repair  
such defect, or replace the product, without charge for parts or labor subject to the following conditions:  
1. All repairs must be performed by VIRTUAL REALITY SOUND LABS® and/or its afliates in Eatontown, New Jersey.  
2. The equipment must not have been altered or been damaged through negligence, accident, or improper operation.  
3. The replacement of parts are exempted from this warranty when replacement is necessary due to normal wear and tear.  
4. All warranty claims must be accompanied by a copy of the sales receipt or bill of sale.  
3. Screw the speaker into  
• Wire Cutter  
Maintain proper polarity by attaching the  
Positive Wire(+) to Positive Terminal(+) and  
the Negative Wire(-) to Negative Terminal(-)  
place with screws (provided).  
• Electric Drill  
with 1/16" bit  
4. Firmly attach the speaker  
grill cover.  
• Hammer  
• Safety Glasses  
• Electrical Tape  
5. Repair or replacement parts supplied by VIRTUAL REALITY SOUND LABS® under this warranty are protected only for the  
unexpired portion of the original warranty.  
6. In the case of car stereos, this warranty does not extend to the elimination of car static or motor noise; correction of antenna  
problems; costs incurred for the removal or reinstallation of the product; damage to tapes, speakers, accessories or car elec-  
trical systems.  
7. VIRTUAL REALITY SOUND LABS® will not be responsible for any charge incurred for installation.  
OWNER’S RESPONSIBILITIES:  
VIRTUAL REALITY SOUND LABS® will make every effort to provide warranty service within a reasonable period of time.  
SHOULD YOU HAVE ANY QUESTIONS ABOUT SERVICE RECEIVED, OR IF YOU WOULD LIKE ASSISTANCE IN OBTAINING  
SERVICE, PLEASE CALL TOLL FREE 1-800-445-1797, 8:30am - 4:30pm EST.  
In order to provide you with the proper warranty service, we request that you adhere to the following procedure:  
1. Include a copy of your sales receipt or bill of sale with your unit when it is returned for warranty service.  
2. If it is necessary to return your product for service, please return it securely packed, preferably in the original shipping carton,  
and freight and insurance prepaid to the following address: VIRTUAL REALITY SOUND LABS, Service Department, 41 James  
Way, Eatontown, New Jersey 07724.  
Speaker wires with female disconnects on  
one end are recommended. When connect-  
ing the speaker wires to your speakers in a  
new installation, you should follow the wiring  
instructions from your audio system’s manu-  
facturer.  
Attach the quick disconnect connectors to  
the speaker terminals as shown. Maintain  
proper polarity by attaching the Positive  
Wire(+) to Positive Terminal(+) and the Nega-  
tive Wire(-) to Negative Terminal(-).  
Before You Install  
We understand that automotive audio equipment installations can be troublesome at  
times, even to the most experienced of installation technicians. If you are not con-  
dent working with electrical wiring, removing and reinstalling interior panels, carpet-  
ing, dashboards or other components of your vehicle, please call our TOLL-FREE help  
line 1-800-445-1797 and our in-house technical service team will answer your instal-  
lation questions.  
3. Please include a detailed explanation of the problem you are having.  
4. If your product is found by VIRTUAL REALITY SOUND LABS® to have a defect in material or workmanship, within the  
warranty period, it will be repaired or replaced at no charge and returned to you prepaid. Where permitted by Iaw VIRTUAL  
REALITY SOUND LABS® liability shall be limited to that set forth in this warranty. This warranty shall be the exclusive remedy  
of the purchaser.  
For most systems the positive wire attaches  
to the positive speaker terminal and the neg-  
ative wire attaches to the negative terminal.  
Before installing these speakers, check the vehicle’s manual for locations of  
important vehicle components such as air bags, CO2 systems, fuel systems,  
& electrical systems installed in the vehicle. Accidental deployment of air bags  
may result in serious injury.  
VIRTUAL REALITY SOUND LABS® makes no other warranty of any kind, expressed or implied; and all implied warranties, are  
hereby disclaimed by VIRTUAL REALITY SOUND LABS® and excluded from this warranty, VIRTUAL REALITY SOUND LABS®  
and/or its afliates, the manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or con-  
sequential, arising out of the use or intended use of the product.  
©2008 Intellectual Solutions Inc., All rights reserved. All designs, logos and images are the exclusive property of Intellectual Solutions  
Inc. and/or its afliates. U.S. and Foreign Patents Pending. 071108 Printed in China 00000  
 

Quadra Fire Stove SAPPHIRE D CSB User Guide
Rangemaster Cooktop RGG60 User Guide
Renesas Network Card M34571T2 CPE User Guide
Ricoh Printer 5560V User Guide
Roland All in One Printer SP 300 User Guide
Roland Electronic Keyboard GR 500 User Guide
Rotel Stereo Amplifier RA 820BX2 User Guide
Ryobi Saw BS901 User Guide
Sanyo Air Conditioner 09KS51 User Guide
Sears Battery Charger 20071440 User Guide