Roadmaster Car Speaker RT15 User Guide

Mounting  
Frequently Asked Questions  
THE RT15 CAN BE MOUNTED 3 DIFFERENT WAYS  
What if there is no sound?  
1. Your stereo may have a blown fuse. Replace fuse with the same amperage and style.  
2. You may have improper wiring. Check all wires for a secure connection.  
Read First!  
Dear Customer,  
What if the sound volume is low?  
Your stereo may not have enough power, you may need to install an amplifier to  
drive the speakers. Connect the RCA jacks to an amplifier.  
Flat Surface Mount  
Angled Surface Mount  
Flush Mount  
Surface Mount  
CONGRATULATIONS. The RT15 Tweeters, when used as described, will give you years of  
dependable service in your car, truck, RV or mini-van. We have taken numerous measures in  
quality control to ensure that your product arrives in top condition, and will perform to your  
satisfaction. In the rare event that your RT15 Tweeters contain a damaged or missing item;  
does not perform as specified; requires warranty service or you have a installation problem,  
DO NOT RETURN THIS PRODUCT TO THE STORE. Please call our TOLL FREE number  
US (800) 445-1797 and ask to speak with a member of our technical service team, or submit  
your questions by E-Mail to [email protected] and a member of our  
technical service team will respond by E-Mail to your questions. Our in-house technical  
service team will expedite delivery of your part, or advise you on installation, or help  
troubleshoot a problem with you. If your product needs warranty service, our technical  
service team representative will help you obtain the fastest remedy possible under the  
warranty.  
1. Twist the surface mounting bracket  
and flush trim bezel and separate  
them from the speaker and wire  
2. Place the flat or angled mounting  
base onto the surface where the RT15  
Tweeter will be installed. Use a marker  
to mark where the screw holes will be.  
Drill pilot holes with a 1/16" drill bit. If  
you want to run the speaker wires  
behind the mounting surface, you will  
have to mark and drill a hole for that as  
well.  
3. Thread the speaker wire from the  
vehicle's audio system, out through the  
hole in the mounting surface, and  
splice them with the speaker wires as  
shown in the wiring section of this  
manual.  
Why do I have a whining noise coming from the speakers?  
You may have poor filtering of your alternator. If that is the case then you  
may need to add an alternator filter to the power lead.  
Mark Screw Holes  
Mark Screw Holes  
Mark Wire Hole  
Why do I have odd sounding noises coming from the speakers?  
You may have corroded battery terminals and/or a weak battery. If the terminals on  
the battery are corroded clean them, then check the sound. If the sound system is still  
making noises check battery strength. If it is low recharge or replace the battery.  
Mark Wire Hole  
Why does the speaker have sound coming from one channel only?  
First make sure the balance control is set correctly. If the balance is set correctly  
your stereo may be defective or the speaker may be defective. To troubleshoot  
this problem you MUST change both positive and negative leads of each channel with  
the positive and negative leads of the opposite channel, if the same speaker has  
no sound then the speaker is no good, if the opposite speaker has no sound then  
your stereo may be defective.  
Angled Surface Mount  
Specifications  
4. Slide the base along the wire, align  
the holes in the base with the pilot  
holes. Use supplied screws to secure  
the base.  
5. Place the surface mount trim bezel  
over the speaker and push until the  
base and the bezel can be twisted  
together.  
• 1" Kevlar Dome Tweeter  
• 0.42 oz. Magnet Weight  
• 10 Watts RMS per Speaker  
• Frequency Range - 2kHZ - 20 kHZ  
• 25mm KAPTON Voice Coil  
• NeFeB Magnet Composition  
• Speaker Wire Length 39" per Speaker  
Give Us a Call, We'll Help You Install  
Flat Surface Mount  
GIVE US A CALL, WE'LL HELP YOU INSTALL.  
Parts  
PLEASE DO NOT RETURN PRODUCT TO STORE.  
Visit us on the WEB  
Flush Mount  
1. Choose  
vehicle that has  
a
location in your  
minimum  
For Information and Technical Assistance,  
Call Toll-Free in U.S.A. and Canada.  
a
The space behind the  
speaker opening must be  
deeper than 1" or 2.54 cm  
to prevent interference  
with any of the vehicle's  
functions or features.  
(i.e.,window operation)  
clearance behind it of at least 1".  
Make sure you can temporarily  
remove the mounting surface so  
you can secure the RT15 tweeter  
with the retaining ring.  
1-800-445-1797  
2 Flush Mount Trim Bezels  
2 Flat Mount Bases  
NOTES  
2. Mark a 2 1/8" diameter circle.  
3. Cut out the circle,  
1"  
4. Thread the speaker wire from the  
vehicle's audio system, out through  
the hole in the mounting surface  
and through the retaining ring.  
Splice the audio system wires with  
the speaker wires as shown in the  
wiring section of this manual.  
5. Take a RT15 speaker fitted with  
the flush mount trim ring and the  
flat mounting base and splice it to  
the speaker wires. (See Wiring)  
6. Insert speaker and wire into  
hole.  
2 1/8"(53.97mm)  
Diameter of Hole  
2 Surface Mount Trim Bezels  
2 Retaining Rings  
2 Speakers & Wire  
Retaining Ring  
Trim Ring  
Parts Shown Unassembled  
2 Angle Mount Bases  
Location  
Speaker & Wire  
Flat Base  
1"  
Before installing this product, you must check the vehicle's manual for locations of  
safety equipment such as air bags and CO2 systems installed in the vehicle. Accidental  
deployment of air bags may result in serious injury.  
Limited Warranty  
VIRTUAL REALITY SOUND LABS® products are designed and manufactured to provide a high level of trouble-free performance. VIRTUAL  
REALITY SOUND LABS® warrants, to the original purchaser, that its products are free from defects in material and workmanship for 30 days  
from the date of original purchase. As part of our commitment to product excellence, VIRTUAL REALITY SOUND LABS® and/or its affiliates  
routinely improve the designs, materials or production methods of its existing products. Because it is impractical to publicize all changes in  
every product, we reserve the right to make such changes without notice.  
Possible Mounting Locations  
The RT15 tweeters can be surface or flush  
mounted. Possible locations for mounting  
the RT15 tweeters are the dashboard, roof  
pillars, interior panels, door panels and  
Wiring  
CONDITIONS OF WARRANTY:  
When connecting the speaker wires  
to your speakers in  
installation, you should follow the  
wiring instructions from your audio  
system’s manufacturer.  
If during the 30 day warranty period your new product is found to be defective, VIRTUAL REALITY SOUND LABS® will repair such defect, or  
replace the product, without charge for parts or labor subject to the following conditions:  
RT15 Tweeters  
Front Channel  
a
new  
ceiling panels. For  
a
flush mounted  
1. All repairs must be performed by VIRTUAL REALITY SOUND LABS® and/or its affiliates in Eatontown, New Jersey.  
2. The equipment must not have been altered or been damaged through negligence, accident, or improper operation.  
3. The replacement of parts are exempted from this warranty when replacement is necessary due to normal wear and tear.  
4. All warranty claims must be accompanied by a copy of the sales receipt or bill of sale.  
installation, there must be a minimum of at  
least 1" of clearance behind the mounting  
surface after the tweeter is installed.  
5. Repair or replacement parts supplied by VIRTUAL REALITY SOUND LABS® under this warranty are protected only for the unexpired portion  
of the original warranty.  
+
+
6. In the case of car stereos, this warranty does not extend to the elimination of car static or motor noise; correction of antenna problems;  
costs incurred for the removal or reinstallation of the product; damage to tapes, speakers, accessories or car electrical systems.  
7. VIRTUAL REALITY SOUND LABS® will not be responsible for any charge incurred for installation.  
OWNER’S RESPONSIBILITIES:  
For most systems the positive wire  
attaches to the positive speaker  
terminal and the negative wire  
attaches to the negative terminal.  
If you are installing the RT15 speakers to upgrade/replace your existing  
speakers, mark the polarity of the speaker wires, disconnect the speaker  
wires and remove the existing speakers from your vehicle. Temporarily place  
the RT15 speakers in the location you selected in your vehicle and connect  
the existing speaker wires. Temporary placement of the speakers in the  
vehicle helps in estimating length of wiring needed, as well as, how the  
speakers will sound in various locations of the vehicle.  
95.5  
VIRTUAL REALITY SOUND LABS® will make every effort to provide warranty service within a reasonable period of time.  
SHOULD YOU HAVE ANY QUESTIONS ABOUT SERVICE RECEIVED, OR IF YOU WOULD LIKE ASSISTANCE IN OBTAINING SERVICE,  
PLEASE CALL TOLL FREE 1-800-445-1797, 8:30am - 4:30pm EST.  
Car Stereo  
In order to provide you with the proper warranty service, we request that you adhere to the following procedure:  
1. Include a copy of your sales receipt or bill of sale with your unit when it is returned for warranty service.  
2. If it is necessary to return your product for service, please return it securely packed, preferably in the original shipping carton, and freight and  
insurance prepaid to the following address: VIRTUAL REALITY SOUND LABS, Service Department, 41 James Way, Eatontown, New Jersey  
07724.  
If you are installing the RT15  
speakers to upgrade/replace your  
existing speakers, mark the polarity  
of the speaker wires, disconnect the  
speaker wires and remove the  
existing speakers from your vehicle.  
Rear Channel  
3. Please include a detailed explanation of the problem you are having.  
4. If your product is found by VIRTUAL REALITY SOUND LABS® to have a defect in material or workmanship, within the warranty period, it will  
be repaired or replaced at no charge and returned to you prepaid. Where permitted by Iaw VIRTUAL REALITY SOUND LABS® liability shall be  
limited to that set forth in this warranty. This warranty shall be the exclusive remedy of the purchaser.  
We understand that automotive audio equipment installations can be  
troublesome at times, even to the most experienced of installation  
technicians. If you are not confident working with electrical wiring, removing  
and reinstalling interior panels, carpeting, dashboards or other components  
of your vehicle, please call our TOLL FREE help line (800)445-1797 and our  
in-house technical service team will answer your installation questions.  
Color of wires are for illustration only.  
VIRTUAL REALITY SOUND LABS® makes no other warranty of any kind, expressed or implied; and all implied warranties, are hereby  
disclaimed by VIRTUAL REALITY SOUND LABS® and excluded from this warranty, VIRTUAL REALITY SOUND LABS® and/or its affiliates, the  
manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or consequential, arising out of the use or  
intended use of the product.  
Recommended Method For Splicing Wires  
#1  
#2  
#3  
©2008 Intellectual Solutions Inc., All rights reserved. All designs, logos and images are the exclusive property of Intellectual Solutions Inc. and/or its affiliates. U.S. and Foreign  
Patents Pending. 071508 Printed in China 00000  
Strip 1/2" of insulation from the ends of the wTirwesis.t together and bend as shown.  
Wrap with electrical tape.  
 

Q Logic Switch 59022 03 D User Guide
Radio Shack Pager PG 202 User Guide
Raritan Computer Server DKX2 0E E User Guide
Rosewill Network Card RC 401 Dual EX User Guide
Ryobi Automobile Parts AC04150T User Guide
Salton Mixer FSHM100 User Guide
Samsung TV DVD Combo DS 21G5 User Guide
Sanyo Camera Lens LNS T03 User Guide
Sanyo Cordless Telephone CLT E23 User Guide
Seiko Printer TM U590 U590P User Guide