Roadmaster Car Speaker VRT18 User Guide

Mounting  
Frequently Asked Questions  
1 Pair VRT18 Ribbon Tweeters  
Before installing this product, you must check the vehicle's manual for  
What makes “Ribbon” tweeters better than” Dome” tweeters?  
Ribbon tweeters use a very low mass metallic ribbon to reproduce faster, more sparkling  
highs. Dome tweeters use the same type of voice coil as regular speakers.  
locations of safety equipment such as air bags and CO2 systems  
installed in the vehicle. Accidental deployment of air bags may result  
in serious injury.  
Read First!  
Dear Customer,  
Don’t “Ribbon” tweeters have lower impedance than 4 Ohms?  
Because “Ribbons” do not use a voice coil they do have lower impedance than dome  
tweeters. This is corrected by a built-in impedance matching transformer that gives them a  
constant 4 Ohm impedance.  
Flat Surface Mount  
1. Attach the flat surface mount  
brackets to the Ribbon tweeters using  
the supplied screws.  
CONGRATULATIONS. The VRT18 Ribbon Tweeters, when used as described, will give you  
years of dependable service in your car, truck, RV or mini-van. We have taken numerous  
measures in quality control to ensure that your product arrives in top condition, and will  
perform to your satisfaction. In the rare event that your VRT18 Ribbon Tweeters contain a  
damaged or missing item; does not perform as specified; requires warranty service or you  
have a installation problem, DO NOT RETURN THIS PRODUCT TO THE STORE. Please  
call our TOLL FREE number US (800) 445-1797 and ask to speak with a member of our  
technical service team, or submit your questions by E-Mail to [email protected]  
and a member of our technical service team will respond by E-Mail to your questions. Our  
in-house technical service team will expedite delivery of your part, or advise you on  
installation, or help troubleshoot a problem with you. If your product needs warranty service,  
our technical service team representative will help you obtain the fastest remedy possible  
under the warranty.  
The frequency response claims 3,000 Hz to 40,000 Hz. Is that real?  
Yes. The human ear cannot hear sounds above 20,000 Hz, but it can perceive harmonics  
well above that. Ribbon tweeters are known for exhibiting extremely wide frequency  
response.  
2. Attach the brackets to the selected  
location using the supplied screws.  
3. Route the wires to the Crossover  
network and connect them by pushing  
down on the Quick release terminals  
and inserting the wires into the holes.  
Release the terminal to secure the  
wire.  
Why is the Crossover network needed? Can’t I just connect the ribbon tweeters  
directly to my speaker wires?  
The Crossover network protects the Ribbon tweeters from being damaged by low  
frequencies. This permits the Ribbons to play at higher volume settings.  
One of my VRT18 Ribbon tweeters is not producing any sound. What should I do?  
Call Technical Service (1-800-445-1797) for assistance.  
Angled Surface Mount  
Specifications  
• 150 Watts Maximum Power per Pair  
• 80 Watts RMS per Pair  
1. Attach the angled surface mount  
brackets to the Ribbon tweeters  
using the supplied screws  
• Impedance: 4 Ohms per Tweeter  
• Frequency Response:  
• Sensitivity: 90 db 1W/1M  
• Crossover Frequency:  
3,500 Hz – 12 db / Octave  
3,000 Hz ~ 40,000 Hz ± 3 db  
• Ribbon Material: Kapton 8mm X 45 mm  
2. Attach the brackets to the  
selected location using the supplied  
screws.  
Give Us a Call, We'll Help You Install  
3. Route the wires to the Crossover  
network and connect them by  
pushing down on the Quick release  
terminals and inserting the wires  
into the holes. Release the terminal  
to secure the wire.  
GIVE US A CALL, WE'LL HELP YOU INSTALL.  
Parts  
PLEASE DO NOT RETURN PRODUCT TO STORE.  
Visit us on the WEB  
For Information and Technical Assistance,  
Call Toll-Free in U.S.A. and Canada.  
1-800-445-1797  
NOTES  
2 Ribbon Tweeters  
2 Tweeter Bezels  
Crossover Network  
4 Wire Splices  
Wiring  
COLOR OF WIRES ARE FOR ILLUSTRATION ONLY.  
2 Hook and Loop Fasteners  
2 Angle Mounting Brackets  
2 Flat Mounting Brackets  
Front Right Tweeter  
Front Left Tweeter  
Crossover Network  
10 Mounting Clips 12 Long Screws 10 Small Screws  
Location  
Before installing this product, you must check the vehicle's manual for  
locations of safety equipment such as air bags and CO2 systems installed  
in the vehicle. Accidental deployment of air bags may result in serious  
Limited Warranty  
VIRTUAL REALITY SOUND LABS® products are designed and manufactured to provide a high level of trouble-free performance. VIRTUAL  
REALITY SOUND LABS® warrants, to the original purchaser, that its products are free from defects in material and workmanship for 30 days  
from the date of original purchase. As part of our commitment to product excellence, VIRTUAL REALITY SOUND LABS® and/or its affiliates  
routinely improve the designs, materials or production methods of its existing products. Because it is impractical to publicize all changes in  
every product, we reserve the right to make such changes without notice.  
Possible Mounting Locations  
The VRT18 Ribbon tweeters can be surface or  
angle mounted. Possible locations for  
mounting the VRT18 Ribbon tweeters are the  
dashboard, roof pillars, interior panels, door  
panels and ceiling panels.  
Front Left Channel  
Front Right Channel  
CONDITIONS OF WARRANTY:  
If during the 30 day warranty period your new product is found to be defective, VIRTUAL REALITY SOUND LABS® will repair such defect, or  
replace the product, without charge for parts or labor subject to the following conditions:  
1. All repairs must be performed by VIRTUAL REALITY SOUND LABS® and/or its affiliates in Eatontown, New Jersey.  
2. The equipment must not have been altered or been damaged through negligence, accident, or improper operation.  
3. The replacement of parts are exempted from this warranty when replacement is necessary due to normal wear and tear.  
4. All warranty claims must be accompanied by a copy of the sales receipt or bill of sale.  
95.5  
5. Repair or replacement parts supplied by VIRTUAL REALITY SOUND LABS® under this warranty are protected only for the unexpired portion  
of the original warranty.  
HEAD UNIT  
6. In the case of car stereos, this warranty does not extend to the elimination of car static or motor noise; correction of antenna problems;  
costs incurred for the removal or reinstallation of the product; damage to tapes, speakers, accessories or car electrical systems.  
7. VIRTUAL REALITY SOUND LABS® will not be responsible for any charge incurred for installation.  
OWNER’S RESPONSIBILITIES:  
If you are installing the VRT18 Ribbon speakers to upgrade/replace your  
existing speakers, mark the polarity of the speaker wires, disconnect the  
speaker wires and remove the existing speakers from your vehicle.  
Temporarily place the VRT18 Ribbon speakers in the location you selected in  
your vehicle and connect the existing speaker wires. Temporary placement of  
the speakers in the vehicle helps in estimating length of wiring needed, as  
well as, how the speakers will sound in various locations of the vehicle.  
Connect the “Front Channel’ speaker wires to the Crossover network inputs.  
The Crossover network has crossover circuits for both Left & Right channels.  
Observe proper polarity for each pair of speaker wires.  
VIRTUAL REALITY SOUND LABS® will make every effort to provide warranty service within a reasonable period of time.  
SHOULD YOU HAVE ANY QUESTIONS ABOUT SERVICE RECEIVED, OR IF YOU WOULD LIKE ASSISTANCE IN OBTAINING SERVICE,  
PLEASE CALL TOLL FREE 1-800-445-1797, 8:30am - 4:30pm EST.  
In order to provide you with the proper warranty service, we request that you adhere to the following procedure:  
1. Include a copy of your sales receipt or bill of sale with your unit when it is returned for warranty service.  
2. If it is necessary to return your product for service, please return it securely packed, preferably in the original shipping carton, and freight and  
insurance prepaid to the following address: VIRTUAL REALITY SOUND LABS, Service Department, 41 James Way, Eatontown, New Jersey  
07724.  
Connect the VRT18 Ribbon Tweeter wires to the Crossover network outputs,  
observing proper polarity for each tweeter.  
3. Please include a detailed explanation of the problem you are having.  
Wires may be spliced using the method shown in the drawing below, or use  
the supplied “Scotchlok” connectors.  
4. If your product is found by VIRTUAL REALITY SOUND LABS® to have a defect in material or workmanship, within the warranty period, it will  
be repaired or replaced at no charge and returned to you prepaid. Where permitted by Iaw VIRTUAL REALITY SOUND LABS® liability shall be  
limited to that set forth in this warranty. This warranty shall be the exclusive remedy of the purchaser.  
We understand that automotive audio equipment installations can be  
troublesome at times, even to the most experienced of installation  
technicians. If you are not confident working with electrical wiring, removing  
and reinstalling interior panels, carpeting, dashboards or other components  
of your vehicle, please call our TOLL FREE help line (800)445-1797 and our  
in-house technical service team will answer your installation questions.  
Recommended Method For Splicing Wires  
VIRTUAL REALITY SOUND LABS® makes no other warranty of any kind, expressed or implied; and all implied warranties, are hereby  
disclaimed by VIRTUAL REALITY SOUND LABS® and excluded from this warranty, VIRTUAL REALITY SOUND LABS® and/or its affiliates, the  
manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or consequential, arising out of the use or  
intended use of the product.  
#1  
#2  
#3  
©2008 Intellectual Solutions Inc., All rights reserved. All designs, logos and images are the exclusive property of Intellectual Solutions Inc. and/or its affiliates. U.S. and Foreign  
Patents Pending. 072308 Printed in China 00000  
Strip 1/2" of insulation from the ends of the wTirwesis.t together and bend as shown.  
Wrap with electrical tape.  
 

Python Automobile Alarm Model 902 User Guide
Radica Games Games 76073 User Guide
RedMax Brush Cutter BCZ3001S User Guide
Renesas Stereo Amplifier 3SK318 User Guide
ResMed CRT Television 61850 2 User Guide
Salter Housewares Building Set E 1053 User Guide
Sanyo Air Conditioner 42TW72R User Guide
Scag Power Equipment Lawn Mower ST 18B Tractor User Guide
Schlage Automobile Electronics WCE100 User Guide
SECO LARM USA Security Camera EV 2866 NKGQ User Guide