Ryobi Saw A31TS04 User Guide

OPERATOR'S MANUAL  
DADO THROAT PLATE  
A31TS04  
(FOR USE WITH THE BTS15 TABLE SAW)  
Your Dado Throat Plate has been engineered and manufactured to Ryobi's high standards for dependability, ease of op-  
eration, and operator safety.  
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual.  
Thank you for buying a Ryobi tool.  
SAVE THIS MANUAL FOR FUTURE REFERENCE  
 
UNPACKING  
INFORMATION  
LOOSE PARTS LIST  
n Remove the loose parts from the box.  
n Dado throat plate  
n Inspect the dado throat plate carefully to make sure no  
n M5 x 10 mm screws (2)  
breakage or damage occurred during shipping.  
TOOLS NEEDED  
Phillips head screwdriver  
n If the dado throat plate is damaged, please call  
1-800-525-2579 for assistance.  
WARNING:  
If any parts are missing, replace the missing parts before assembling the kit. Failure to do so could result in serious  
personal injury.  
M5 X 10 MM  
SCREWS  
THROAT PLATE  
ASSEMBLY  
INSTALLING A DADO INSERT  
See Figures 1-2.  
BTS15 TABLE SAW PRIOR TO DADO INSERT INSTALLATION  
n Unplug the saw.  
WARNING:  
Do not allow familiarity with tools to make you careless.  
Remember that a careless fraction of a second is  
sufficient to inflict severe injury.  
WARNING:  
Failure to turn the saw off, remove the switch key,  
and unplug the saw could result in accidental starting  
causing possible serious personal injury.  
Fig. 1  
3
 
ASSEMBLY  
n Lower the blade below the table surface.  
DADO INSERT  
TABLE TOP  
n Loosen the screws and remove the throat plate.  
SCREWS  
n Remove the blade and blade guard assembly following  
instructions in the table saw Operator's Manual.  
n Included with the dado set are installation instructions.  
Follow these instructions to install the dado set.  
NOTE: The spacer/washer should only be used with a  
regular blade.  
NOTE: When using 5/8 in. width dado set use flange nut  
and flange/spacer.  
n Place dado insert on the table saw as shown in figure 1.  
n Securely tighten using screws provided.  
WARNING:  
Fig. 2  
Never stand directly in line with the blade or allow hands  
to come closer than 3 in. to the blade. Do not reach  
over or across the blade. Failure to heed this warning  
can result in serious personal injury.  
OPERATION  
APPLICATIONS  
You may use this tool for the purposes listed below:  
WARNING:  
Always use push sticks or push blocks when making  
non-through cuts to avoid the risk of serious injury.  
Never feed wood with your hands.  
nFor cutting up to 5/8 in. maximum width dadoes on BTS15  
Ryobi table saw.  
WARNING:  
n Follow all dado instructions.  
n When the work is complete, turn the saw off, remove the  
Never install a dado set to cut a larger groove than a  
width of 5/8 in. Installing a wider dado set could result  
in insufficient thread engagement of the arbor nut.  
Never use any blade or dado set with less than full  
engagement of the nut on the threaded arbor shaft.  
Insufficient thread engagement could result in the blade  
or dado loosening on the arbor shaft and could result in  
serious personal injury.  
switch key, and unplug the saw.  
n Lower the blade below the table surface.  
WARNING:  
Lower the blade to prevent possible injury.  
n Remove the dado insert and dado set.  
n Reinstalltheblade,bladeguardassembly,andthroatplate  
USING A DADO INSERT  
following instructions in the BTS15 Operator's Manual.  
n Make sure the wood is not touching the blade. Plug in the  
saw, insert the switch key, and turn the saw on. Let the  
saw build up to full speed before feeding the workpiece  
into the blade. Always use push sticks or push blocks  
with any non-through cuts.  
WARNING:  
To reduce the risk of injury and before plugging the  
saw back in, make sure the blade guard is installed  
and working properly.  
NOTE: Never use this dado throat plate with a dado set  
larger than 6 in..  
4
 
NOTES  
5
 
OPERATOR'S MANUAL  
DADO THROAT PLATE  
A31TS04  
(FOR USE WITH THE BTS15 TABLE SAW)  
WARRANTY  
Ryobi warrants its accessories for a period of 90 days from the date of purchase. Batteries and chargers are  
warranted for a period of two years from the date of purchase.  
PARTS AND SERVICE  
For parts or service, contact your nearest Ryobi authorized service center. Be sure to provide all relevant  
information when you call or visit. For the location of the authorized service center nearest you, please call  
RYOBI TECHNOLOGIES INC.  
1428 Pearman Dairy Road Anderson SC 29625  
Post Office Box 1207 Anderson SC 29622-1207  
Phone 1-800-525-2579  
983000-629  
11-04  
 

Rangemaster Ventilation Hood RMG1H60SG User Guide
Remington Hair Dryer DS 1000 User Guide
Rival Waffle Iron DC WM169 User Guide
Ryobi Outdoor Trimmer P2600 User Guide
Samsung Cell Phone 12172009 User Guide
Samsung Refrigerator DA68 01258A User Guide
Samsung Security Camera VKKF004NUS User Guide
Sanyo Battery Charger KR 1200AAE User Guide
Saturn Automobile 2006 Vue User Guide
Sears Snow Blower 536886531 User Guide