Schlage Automobile Electronics WCE100 User Guide

Camera User Guide  
There are two cameras available for use with the Schlage  
LiNK system.  
WCW100  
The WCW100 is a wireless camera that communicates  
with the Schlage LiNK system through your existing  
wireless router.  
WER  
PO  
WER  
PO  
WCE100  
K
R
O
ETW  
K
R
O
ETW  
N
N
The WCE100 is a wired camera that communicates with  
the Schlage LiNK system through your existing router.  
DO NOT connect Ethernet or power before  
enrolling the camera.  
WCW100 Wireless Camera  
WCE100 Wired Camera  
!
For indoor use ONLY!  
Wireless Antenna (WCW100 Only)  
Rotate the wireless antenna onto the threaded post to ensure clear wireless  
communication. Antenna can be adjusted to obtain a better signal. Best results  
are usually obtained by positioning the antenna vertically.  
Attaching the Antenna  
Camera Stand  
Install the camera stand to provide a steady base for the camera.  
1. Loosen the plastic nut on the back of the camera.  
2. Rotate the threaded post upwards.  
3. Rotate the camera onto the threaded post until it stops.  
4. Tighten plastic washer against camera to secure.  
Plastic  
Washer  
Threaded  
Post  
Plastic  
Nut  
Attaching the Camera to the Stand  
 
Enrolling the Camera  
Camera enrollment is done using the www.schlagelink.com web site.You must have an active account before enrolling the  
camera.  
1. Make sure Ethernet and power are not plugged in to the camera.  
2. Log on to your account at www.schlagelink.com.  
3. Click the Cameras tab.  
4. Click the Add Cameras link.  
5. Follow the on-screen instructions.  
Î When enrolling a wireless camera, DO NOT disconnect the Ethernet cable until instructed to do so on  
the web site.  
Modifying the Camera Settings  
1. Log on to your account at www.schlagelink.com.  
2. Click on the Cameras tab.  
3. Click the Edit Settings button next to the camera you want to edit.  
4. To modify the wireless settings, click the Setup Wireless button.  
Rebooting the Camera  
1. Unplug A/C power.  
2. Unplug Ethernet (if necessary).  
3. Reconnect A/C power.  
4. Connect Ethernet cable (do this for both wired and wireless cameras).  
5. For wireless camera, log on to your account at www.schlagelink.com and click the Cameras tab, then click  
Reconnect Wireless.  
Moving the Camera to a Different Account  
The camera cannot be enrolled in two accounts at the same time. To move the camera to a different account, you must  
first remove the camera from one account, and then enroll it into the new account.  
1. Login to your account at www.schlagelink.com.  
2. Click Cameras.  
3. Click Edit Cameras.  
4. Click Remove next to the camera you want to move.  
5. Follow the on-screen instructions for removal.  
6. Once the camera is removed from the account, it can be added to a different account. See Enrolling the Camera  
for more information.  
Lights  
Light  
Light Behavior  
Green Steady  
Off  
Description  
Power On  
Power Off  
Start Up  
Power  
POWER  
NETWORK  
Green Blinking  
Green Steady  
Off  
Network  
Power On  
Wireless or LAN not connected, or  
camera is not sending/receiving data  
Green Blinking  
Sending/receiving data  
 
 
Troubleshooting and FAQ  
1. The SSID is case-sensitive.  
2. If there is a space in your SSID, change the SSID so there is no space and try again.  
3. If your SSID is not showing up on the web interface, it may not be broadcast. Reference the instructions that came  
with your router for more information.  
I don’t have my router instructions and I don’t know how to change a setting.  
1. Search on your exact make and model using an online search engine. Most manufacturers maintain their  
instructions online.  
password will be required. This information should be available in the manufacturer’s instructions.  
I cannot remember my router SSID/password.  
1. Most routers can be reset using a physical button on the router. Refer to the router instructions for more information.  
Resetting your router will restore factory settings.This could cause other computers or devices to stop  
communicating with your router. Refer to the router instructions and/or the person who set up your router  
for more information.  
2. Once you have reset your router, the default settings can be used. Refer to the router instructions for more  
information.  
The camera was working, but has stopped working.  
1. Ensure that power is connected.  
2. Ensure that the Ethernet cable is connected (WCE100).  
3. Check LED indicators. See LED Indicators for more information.  
4. Ensure the settings on your router match the settings for the camera. If you have recently changed your SSID,  
password or security type, the camera’s information will also need to be changed.  
5. Try rebooting the camera. See Rebooting the Camera for more information.  
I cannot see the camera video on my phone.  
2. Click My Phones.  
3. Click Edit Phone.  
4. Click to check the check box next to the camera you want to be displayed on the phone.  
5. If your phone application is currently open, then close the phone application and re-open it for the new setting to  
take effect.  
I installed the camera, but the video is not displayed on the Cameras tab, and the text “Viewer here” is displayed.  
Download and install the Adobe Shockwave™ player. The player can be downloaded from get.adobe.com/shockwave.  
Why does video turn off after 2 minutes?  
The camera is intended to provide visual verification of current or triggered events, which generally are accomplished in  
2 minutes or less. Video can be continued for additional 2 minute segments by selecting the PLAY icon.  
Can a camera be connected to more than one LiNK account simultaneously?  
No. See Moving the Camera to a Different Account for more information.  
Is video storage available?  
Not at this time. Video storage may be available in the future. Check link.schlage.com for updates.  
Is pan/tilt/zoom available?  
Not at this time. Check link.schlage.com for updates.  
 
Can the camera be mounted outside?  
No, the camera is not designed for outdoor use.  
Can I install more than one camera onto my LiNK account?  
Yes. Follow the instructions for Enrolling the Camera for each additional camera.  
Is video secure?  
Yes, the camera creates a secure connection directly to the video server so that video is not accessible outside that  
connection.  
Can I use cameras from other manufacturers?  
Not at this time. The Schlage LiNK camera is designed to provide a secure video connection, along with easy plug and  
play installation, not currently available with other cameras. Check link.schlage.com for updates.  
©2009 Schlage Lock Company  
camera user guide Rev. 08/09-b  
 

PYLE Audio Stereo System PDSP850 User Guide
PYLE Audio Stereo System PLCD14MRKT User Guide
RCA Camcorder CC6374 User Guide
Renesas Network Card HD6417641 User Guide
Saeco Coffee Makers Coffeemaker HD8772 User Guide
Samsung Fax Machine SF 750 Series User Guide
Samsung Flat Panel Television HP R4262 User Guide
Samsung Satellite TV System SL10D10 User Guide
Scag Power Equipment Lawn Mower SFZ48 19KA User Guide
Sears Power Supply 20071520 User Guide